Flow Measurement || Civil Engineering || 60 Previous Year Questions

1.If H is the head over the crest of a rectangular weir, the discharge varies as :
1.यदि आयताकार बंधिका के शीर्ष के ऊपर का हेड H है, तो निर्वहन में परिवर्तन किसके अनुरूप होगा?
(A) H
(B) H^1.5
(c) H^2.8
(d) 10^0.5
Ans – B.

2.At critical flow conditions in a rectangular channel, the value of Froude number is-
2.एक आयताकार चैनल में क्रांतिक प्रवाह की दशाओं में, फ्राउड संख्या का मान होगा।
(a) Two/दो
(b) Zero/शून्य
(c) Infinity/अनंत
(d) Unity/एकक
Ans – D.

3.The discharge through a trapezoidal channel is maximum when-
3.एक समलंबाकार चैनल के माध्यम से निर्वहन तब अधिकतम होता है, जब
(a) Top width = 1.5x sloping side/शीर्ष चौड़ाई=1.5x ढलान की भुजा
(b) Half of top width = one of the sloping sides/ शीर्ष चौड़ाई का आधा = ढलान की भुजाओं में से एक
(c) Top width = Half of sloping side/शीर्ष चौड़ाई =ढलान की भुजा का आधा
(d) Half of top width = half of the sloping side/ शीर्ष चौड़ाई का आधा = ढलान की भुजा का आधा
Ans – B.

4.The reason for using curved vanes over flat vanes in a hydrulic turbine is
4.किसी हाइड्रोलिक टरबाइन में समतल वेन की जगह वक्रित वेन का उपयोग करने का क्या कारण है?
(a) low maintenance cost/कम रखरखाव लागत
(b) higher hydraulic efficiency can be obtained/उच्च हाइड्रोलिक दक्षता प्राप्त की जा सकती है
(c) high velocity jets can be used/उच्च वेग वाले जेट का उपयोग किया जा सकता है
(d) convenience of machining/मशीनिंग की सुविधा
Ans – B

5.Venturimeter is based on the principle of-
5.वेन्चुरीमीटर किस सिद्धांत पर आधारित है?
(a) Euler’s equation of motion/ऑयलर का गति का समीकरण
(b) Reynold’s equation of motion/रेनॉल्ड्स का गति का समीकरण
(c) Navier-Stokes equation/नेवीअर-स्टोक्स का समीकरण
(d) Bernoulli’s equation/बर्नोली का समीकरण
Ans – D.

6.Which device is used for measuring the descharge
(a) Manometers/मैनोमीटर
(b) Pitot-tube/पिटॉट ट्यूब
(c) Venturimeter/वेन्चुरीमीटर
(d) All of these/ये सभी
Ans.C.

7.A laser-doppler anemometer is a device to measure
7.लेजर-डॉप्लर एनीमोमीटर क्या मापने का उपकरण है
(a) shear stress at a boundary/सीमा पर कर्तन तनाव
(b) surface tension of a fluid/तरल पदार्थ का पृष्ठ तनाव
(c) the turbulent velocity fluctuation in a flow/प्रवाह में विक्षुब्ध वेग का विक्षोभ
(d) dragforce on an aerofoil/एरोफोयल पर ड्रैग बल
Ans.C.

8.The overflowing sheet of water on a weir is called-
8.बीयर के ऊपर पानी के अति प्रवाह शीट को कहा जाता है-
(a) Head /हेड
(b) Nappe /नेपी
(c) Upstream /प्रतिप्रवाह
(d) Crest/क्रिस्ट
Ans-B.

9.A hydrometer is used to measure
9.उत्प्लव घनत्वमापी का प्रयोग मापने के लिए किया जाता है-
(a) Velocity of fluids/तरलों का वेग
(b) Velocity of gases/ गैसों का वेग
(c) Flow of fluids/तरलों का प्रवाह
(d) Specific gravity of liquids/द्रवों का विशिष्ट घनत्व

Ans- D.

10.Which of the following parameter is measured with the help of elbow meter?
10.निम्न में से कौन-सा पैरामीटर एल्बो मीटर की मदद से मापा जाता है?
(a) Acceleration
(b) Velocity/वेग
(c) Viscosity/श्यानता
(d) Discharge/विसर्जन
Ans-D.

11.Which of the following is measured with the help of an orifice meter?
11.निम्न में से कौन-सा ऑरिफिस मीटर की सहायता से मापा जाता है?
(a) Discharge / निर्वहन
(b) Discharge coefficient / निर्वहन गुणांक
(c) Head of water/ पानी की ऊँचाई
(d) Pressure coefficient / दबाव गुणांक
Ans-A.

12.. ……….is known as the ratio of rate of change of discharge of an outlet and parent channel
12.किसी निर्गम एवं मूल चैनल के निस्सरण के परिवर्तन की दर के अनुपात को को ……….के रूप में जाना जाता है
(a) Efficiency/दक्षता
(b) Flexibility/लचीलापन
(c) Sensitivity/संवेदनशीलता
(d) Modular limit/प्रमापीय सीमा
Ans-B

13.A current meter measures the velocity of flow, if it is held………….
13.एक धारा मीटर प्रवाह के वेग को मापता है, यदि इसे से ……….पर रखा जाता है
(a) on the surface of water/जल की सतह पर
(b) at a mid-point of the cross-section/अनुप्रस्थ काट के मध्य बिंदु
(c) at any point within the cross-section/अनुप्रस्थ काट में किसी भी बिंदु
(d) at the bottom of channel/सरणी के नीचे
Ans-C.

14.Which of the following is best instrument for measuring the velocity of a stream flow?
14.निम्नलिखित में से कौन सा यंत्र धारा प्रवाह के वेग के मापन के लिए सर्वाधिक उपयुक्त है?
(a) Pitot tube/पिटॉट ट्यूब
(b) Price’s current meter/प्राइस का करंट मीटर
(c) Surface float/सरफेस फ्लोट
(d) Sub-surface float/सब-सरफेस फ्लोट
Ans- B.

15.Which one of the following is NOT a direct stream flow measurement technique?
15.इनमें से क्या एक प्रत्यक्ष धाराप्रवाह मापन तकनीक नहीं है?
(a) Dilution method
(b) Ultrasonic method/पराध्वनिक विधि
(c) Area-velocity method/क्षेत्रफल-वेग विधि
(d) Slope area method/ढलान क्षेत्रफल विधि
Ans- D.

16.The discharge over a broad-crested weir is maximum when the depth of flow is :
16.चौड़ा शिखर वीयर के ऊपर विसर्जन अधिकतम होता है जब प्रवाह की गहराई हो?
A. H/2
B. 2H/3
C. H/4
D. H/5
Ans- B.

17.Cipolletti weir is type of trapezoidal weir in which the sides have a slope of:
17.सिपोलेटी वीयर समलम्बी वीयर का वह प्रकार होता है जिसके पार्श्व की ढाले होती है-
(a) 1 Horizontal to 2 vertical/1 क्षैतिज से 2 उर्ध्वाधर
(b) 1 Horizontal to 3 vertical/1 क्षैतिज से 3 उर्ध्वाधर
(c) 1 Horizontal to 4 vertical/1 क्षैतिज से 4 उर्ध्वाधर
(d) 60° slope/60° ढाल
Ans-C

18.The side slope of cipolletti weir is generally kept
18.सामान्यतः सिपोलेटी वीयर का किनारे की ओर ढाल रखा जाता है।
(a) 1 to 2/1 से 2
(b) 1 to 3/1 से 3
(c) 1 to 4/1से 4
(d) 1 to5/1 से 5
Ans-C.

19.Cipolletti weir is a trapezoidal weir with………
19.सिपोलेटी वीयर एक समलम्बाकार वीयर है………..
(a) sides having end contractions/जिसके किनारे संकुचित होते हैं
(b) side slope 1 V to 4 H / जिसका पार्श्व ढाल 1 ऊधिर व 4 क्षैतिज होता है
(c) side slope 1 H to 4 V / जिसका पार्श्व ढाल 1 क्षैतिज व 4 ऊर्ध्वाधर होता है
(d) side slope 1 V to 1 H / जिसका पार्श्व ढाल 1 ऊर्ध्वाधर व 1 क्षैतिज होता है
Ans-C.

20.Which one of the following is not used for measuring flow through open channel?
20.निम्न में से कौन सा, एक खुले जल संयोजक से प्रवाह मापन में प्रयुक्त नहीं होता है?
(a) Gates/कपाट
(b) Weir/वीयर
(c) Orifice meter/आरफिस मीटर
(d) Venturiflume/वेंचुरीफ्लुम
Ans- C

21.Discharge Q in a triangular weir varies as-
21.किसी त्रिभुजाकार वीयर में विर्सजन Q किस रुप में बदलता है-
(a) H
(B) H^0.5
(C) H^1.5
(d) H^2.5
Ans-D

22.The discharge through a V-notch varies as-
22.नॉच पर निस्सरण निम्न के अनुसार बदलता है-
(A) H
(B) H^5/2
(c) H^3/2
(d) H^1/2
Ans-B.

23.The discharge through a V-notch varies

  1. v-नॉच में से निस्सरण किस अनुसार परिवर्तित होता है?
    (a) proportional to head (H)/दाबोच्चता (H) के समानुपातिक
    (b) inversely proportional to angle /कोण (0 के व्युत्क्रमानुपातिक
    (c) inversely proportional to tan 0/2 / tan 6/2 के व्युत्क्रमानुपातिक
    (d) proportional to H^5/2/H^5/2 के समानुपातिक
    Ans-D.

24.The instrument used for accurately measuring velocity of water is
24.पानी का वेग परिशुद्धता से मापने के लिये उपयोग होने वाला यंत्र है
(a) Pitot tube/पिटाट ट्यूब
(b) V-notch/V-नॉच
(C) Differential U-tube
(d) Manometer/मैनोमीटर
Ans-A.

25.Which of the following device is used for measuring velocity of flow at any point in a pipe?
25.निम्न में से किस डिवाइस का उपयोग पाइप में किसी भी बिंदु पर प्रवाह के वेग के मापन के लिए किया जाता है?
(a) Pitot tube/पिटाट ट्यूब
(b) V-notch/V-नॉच
(C) Differential U-tube
(d) Manometer/मैनोमीटर
Ans-A.

26.Pitot tube is used to measure……
26.पिटॉट ट्यूब का उपयोग ~ मापने में किया जाता है।
(a) Discharge/ विसर्जन
(b) Average velocity/औसत वेग
(c) Velocity at a point/एक बिन्दु पर वेग
(d) Pressure at a point /एक बिन्दु पर दबाव
Ans- C.

27.The Pitot tube is used to measure :
27.पिटॉट नली का प्रयोग क्या नापने के लिए किया जाता है-
(a) Static pressure/स्थैतिक दाब
(b) Stagnation pressure
(C) Velocity at stagnation point/प्रगतिरोध बिंदु पर वेग
(d) Dynamic pressure/ifach und
Ans : (c)

28.Notch are used to measure-
28.खाँच का प्रयोग होता है-
(a) discharge / विसर्जन
(b) pressure / दाब
(c) velocity / वेग
(d) static energy / स्थैतिक ऊर्जा
Ans : (a)

29.Notch is used in any tank or channel for measurement of
29.निम्नलिखित को नापने के लिये किसी टैंक अथवा चैनल में नाँच लगाई जाती है-
(a) Flow rate/बहाव नापने के लिये
(b) Velocity/वेग नापने के लिये
(c) Pressure/दबाव नापने के लिये
(d) All above/उपरोक्त सभी
Ans-A.

30.Notch is device used for measuring
30.नाँच वह उपकरण है जिसे निम्नलिखित को नापने में उपयोग किया जाता है-
(a) Rate of flow through small channel/एक छोटी वाहिका में बहाव दर
(b) Rate of flow through pipes/पाइप में प्रवाह दर
(c) Velocity of flow through a pipe/पाइप में बहाव वेग
(d) Velocity of flow through a small channel/एक छोटी वाहिका में बहाव वेग
Ans- A.

31.In any channel, notch is used to measure the following
31.किसी चैनल में नॉच निम्नलिखित के मापने के लिए प्रयोग की जाती है-
(a) discharge / विसर्जन
(b) pressure / दाब
(c) velocity / वेग
(d) static energy / स्थैतिक ऊर्जा
Ans : (a)

32.Which device is used for temporary measurements of flow?
32.कौन सा उपकरण प्रवाह के अस्थायी मापन के लिए। उपयोग किया जाता है।
(a) Pitot static tube/पिटॉट स्थैतिक ट्यूब
(b) Dull flow tube/मन्द प्रवाह ट्यूब
(c) Venturimeter/वेन्चुरीमीटर
(d) Orifice plate/आरिफिस प्लेट
Ans : (d)

33.The characteristic feature of a barrage is
33.एक बैराज की अभिलाक्षणिक विशेषता है
(a) Provision of raised crest/उठान शिखर पर प्रावधान
(b) Creation of storage reservoir on upstream/अपस्ट्रीम पर भंडारण जलाशय का निर्माण
(c) Provision of series of gates across the river for flow regulation/प्रवाह विनियमन के लिए नदी के पार फाटकों की श्रृंखला का प्रावधान
(d) That it is built in delta areas only/केवल डेल्टा क्षेत्रों में बनाया गया है पिटॉट ट्यूब
Ans-C.

34.For which of the following, Anemometer is used to measure?
34.किसे मापने के लिए एनीमोमीटर का इस्तेमाल किया जाता है?
(a) Viscosity/ श्यानता
(b) Velocity/वेग
(c) Pressure/दबाव
(d) Densitv/घनत्व
Ans : (b)

35.In a venturi flume the flow takes place at:
35.एक वेन्चुरी अवनलिका में बहाव निम्नलिखित पर होता है-
(a) gauge pressure/गेज दाब पर
(b) absolute pressure/निरपेक्ष दाब पर
(c) atmospheric pressure/वायुमंडलीय दाब पर
(d) none of the above/इनमें से कोई नहीं
Ans- B.

36.The concept of boundary layer was first introduced by:
36.सीमांत परत की अवधारणा निम्नलिखित के द्वारा प्रस्तुत की गयी
(a) Newton/न्यूटन
(b) Reynold/रेनॉल्ड
(c) Prandtl/प्रेन्डटल
(d) Kutter/कटर
Ans : (c)

37.Pitot tube measures-
37.एक पिटोट नली द्वारा निम्न का मापन किया जाता है-
(a) pressure head only/केवल दाब शीर्ष
(b) Total head only/केवल कुल (Total) शीर्ष
(c) Velocity head only/केवल वेग शीर्ष
(d) Above all/उपर्युक्त सभी
Ans : (b)

38.A current meter is used to measure the
38.करंट मीटर से मापा जाता है
(a) velocity of flow of water/पानी के प्रवाह का वेग
(b) depth of flow of water/पानी के प्रवाह की गहराई
(c) discharge/विसर्जन
(d) none of the above/उपरोक्त में से कोई नहीं
Ans- A.

39.A submerged weir is one in which the water level on the down streams side of the weir is :
39.निमग्न वीयर वह होता है जिसमें वीयर के अनुप्रवाह पार्श्व में जल का स्तर
(a) Just at the crest level/ठीक शिखर के स्तर पर हो
(b) Below the crest level/शिखर के स्तर से नीचे हो
(c) Above crest level/शिखर के स्तर से ऊपर हो
(d) At same elevation as water surface on upstream/उसी ऊँचाई पर हो जिस पर प्रतिप्रवाह में जल का पृष्ठ है
Ans : (c)

40.Which of the following notch gives the most accurate result while measuring small discharge?
40.अल्प विसर्जन नापने में कौन सा नाँच शुद्धतम परिणाम | देता है?
(a) Rectangular notch/आयताकार नॉच
(b) Trapezoidal notch/समलम्बाकार नॉच
(c) Triangular notch
(d) Cipolletti notch/सिपोलेट्टी नॉच
Ans-C.

41.For a given discharge through an orifice meter, the magnitude of Coefficent of discharge lies between
41.आरिफिस मीटर से दिए गए विसर्जन हेतु, विसर्जन का स्थिरांक के बीच होता है।
(a) 0.51-0.65
(b) 0.64-0.76
(c) 0.76-0.85
(d) 0.86-0.98
Ans : (b)

42.A weir, generally used as a spillway of a dam is:
42.आम तौर पर एक बांध के उत्प्लव मार्ग के रूप में एक वीयर प्रयोग किया जाता है-
(a) Narrow crested weir/संकीर्ण शिखर वीयर
(b) Broad creseted weir/व्यापक शिखर वीयर
(c) Ogee weir/ओजी वीयर
(d) Submerged weir
Ans : (c)

43.Flow duration curve is the graph drawn between
43.प्रवाह काल वक्र निम्नलिखित के मध्य खींचा गया ग्राफ है
(a) Discharge time/निस्सरण काल
(b) The discharge and the percentage of the time such discharge is exceeded/निस्सरण एवं समय काल का वह प्रतिशत जब निस्सरण बढ़ जाता है
(c) Cumulative rate of flow/प्रवाह की संचयी दर
(d) Cumulative volume of flow/प्रवाह की संचयी आयतन
Ans : (b)

44.For accurate flow measurement in channels. an arrangement for aeration under the nappe is necessary when the weir used is:
44.खुले हुए मार्ग में सटीक प्रवाह को मापने के लिए, नेपी के अंतर्गत वातन के लिए प्रबंधन तब जरूरी है। जब हैं।
(a) Contracted rectangular/अनुबंधित आयताकार
(b) Triangular
(c) Submerged contracted rectangular/निमज्जित अनुबंधित आयताकार
(d) Suppressed rectangular./निरुद्ध आयताकार
Ans : (c)

45.Discharge over anogee weir remains the same as that
45.एक ओजी वीयर के ऊपर स्त्राव निम्न में से किसके साव के समान होगा?
(a) Drowned iveir/ड्राउंड वीयर
(b) Triangular weir/त्रिकोणीय वीयर
(c) Sharp crested weir
(d) Cipoletti weir
Ans- D.

46.In a broad-creasted weir, the discharge is maximum if the head of water on the downstream side of weir is…..the head of water on the upstream side of weir:
46.एक चौड़े शिखर वीयर के प्रति प्रवाह की ओर जल के शिखर से विसर्जन अधिकतम होगा यदि वीयर के नीचे की ओर जल शीर्ष वीयर के ऊपर के शीर्ष का है-
(a) Equal to/बराबर है
(b) One third/एक तिहाई है
(c) Two third/दो तिहाई है
(d) Three-fourth/तीन-चौथाई है
Ans : (c)

47.The discharge over a rectangular notch is
47.एक आयताकार नॉच के ऊपर विसर्जन होता है-
(a) Inversely proportional to H^2/3/H^2/3 प्रतिलोमीय अनुपाती
(b) Directly proportional to H/2H/2 का सीधा अनुपाती
(c) Inversely proportional to H^3/2/H^3/2 का प्रतिलोमीय अनुपाती
(d) Directly proportional to HS/2
Ans- C.

48.A weir is said to be narrow-crested, if the width of the crest of the weir is
48.एक वीयर लघु शिखरीय कहलाता है, यदि वीयर के शीर्ष की चौड़ाई है-
(a) Equal to H/H के बराबर
(b) More than H/H से अधिक
(c) Less than H/H से कम
(d) None of the above/उपरोक्त कोई नहीं
Ans : (c)

49.The best method for measuring the velocity of flow in rivers is
49.प्रवाह वेग को नदियों में मापने की सबसे उत्तम विधि है-
(a) Pitot tube method/पिटॉट ट्यूब विधि
(b) Surface float method/सतह प्लव विधि
(c) Velocity rod method/वेग छड़ विधि
(d) Current meter method
Ans- D.

50.The upper surface of weir over which water flows is known as
50.बंधिका के जिस ऊपरी सतह पर पानी बहता है उसे निम्नलिखित के रूप में जाना जाता है
(a) Nappe/नैपी
(c) Sill/ चौखट
(b) Crest/शिखर
(d) Vein/शिरा
Ans- B.

51.Rotameter is used to measure
51.एक रोटामीटर से मापा जाता है।
(a) Velocity of fluid/द्रव के प्रवाह का वेग
(b) Kinetic energy of fluid/द्रव की गतिज ऊर्जा
(c) Viscosity of fluid/द्रव की श्यानता
(d) Flow of fluid/द्रव का प्रवाह
Ans- D.

52.Rotameter is used to measure?
52.रोटामीटर को मापने के लिए प्रयोग किया जाता है।
(a) Pressure/दबाव
(b) velocity/वेग
(c) viscosily/श्यानता
(d) Flow/प्रवाह
Ans- D.

53.Discharge in clear overfall flume depends upon
53.स्पष्ट ओवर फाल नलिका में विसर्जन निर्भर करता है-
(a) The depth of water over the crest/शिखर पर पानी की गहराई
(b) Depth of water on upper stream side/ऊपरी धारा पक्ष पर पानी की गहराई
(c) Depth of water on downstream side/निचली धारा पक्ष पर पानी की गहराई
(d) The depth of water below the crest/शिखर के नीचे पानी की गहराई
|Ans : (a)

54.Which of the following device is not used to measure the rate of flow :
54.निम्नलिखित में से कौन सी युक्ति का प्रयोग प्रवाह दर मापने में नहीं किया जाता है-
(a) Venturimeter/वेन्चुरीमीटर
(b) Pitot tube/पिटॉट ट्यूब
(c) Orificemeter/ऑरिफिस मीटर
(d) Rotameter/रोटामीटर
Ans- B.



from WordPress https://ift.tt/2ZhzzOv
via IFTTT

Comments

Popular posts from this blog

Civil Engineering || HPGK || Previous Years Questions

All india level Je/AE Questions Quiz- 6